3d7428 monolithic 8-bit programmable delay line (series 3d7428 ? low noise) d a ta delay devices, i n c. ? 3 f e a t u r e s p a c k a g e s 1 2 3 4 8 7 6 5 in so ae gn d vdd ou t sc si 3 d 742 8z-x x so i c 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 in ae so /p 0 p1 p2 p3 p4 gnd vdd out md p7 p6 sc p5 si 3d 74 28-xx dip 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 in ae so / p 0 p1 p2 p3 p4 gnd vdd out md p7 p6 sc p5 si 3d 7428s-x x so l f o r mechanical dimensions, click here . f o r package marking details, click here . ? all-silicon, low-power cmos technology ? ttl/cmos compatible inputs and outputs ? vapor phase, ir and wave solderable ? auto-insertable (dip pkg.) ? leading- and trailing-edge accuracy ? programmable via serial or parallel interface ? increment range: 0.25 through 20.0ns ? delay tolerance: 0.5% (see table 1) ? supply current: 3ma typical ? temperature stability : 1.5% max (-40c to 85c) ? vdd stability : 0.5% max (4.75v to 5.25v) functional description pin descriptions in signal input out signal output md mode select ae address enable p0-p7 parallel data input sc serial cloc k si serial data input so serial data output vdd +5 volts gnd ground the 3d7428 device is a versatile 8-bit programmable monolithic delay line. the input (in) is reproduced at the output (out) without inversion, shifted in time as per the user selection. delay values, programmed either via the serial or parallel interface, can be varied over 255 equal steps according to the formula: t i,nom = t inh + i * t inc where i is the programmed address, t inc is the delay increment (equal to the device dash number), and t inh is the inherent (address zero) delay. the device features both rising- and falling-edge accuracy. the all-cmos 3d7428 integrated circuit has been designed as a reliable, economic alternative to hybrid ttl programmable delay lines. it is offered in a standard 16-pin auto-insertabl e dip and a surface mount 16-pin sol. an 8-pin soic package is available for applications where the parallel interface is not needed. table 1: part number specifications pa rt dela ys a nd tolera nces input restrictions number inherent delay (ns) delay range (ns) delay step (ns) rec?d max frequency a b solute max frequency rec?d min pulse w i dth a b solute min pulse w i dth 3d7428-0.25 10.5 2.0 63.75 0.4 0.25 0.12 6.25 mhz 77 mhz 80.0 ns 6.5 ns 3d7428-0.5 10.5 2.0 127.5 0.5 0.50 0.25 3.12 mhz 45 mhz 160.0 ns 11.0 ns 3d7428-1 10.5 2.0 255.0 1.0 1.00 0.50 1.56 mhz 22 mhz 320.0 ns 22.0 ns 3d7428-1.5 10.5 2.0 382.5 1.5 1.50 0.75 1.04 mhz 15 mhz 480.0 ns 33.0 ns 3d7428-2 10.5 2.0 510.0 2.0 2.00 1.00 781 khz 11 mhz 640.0 ns 44.0 ns 3d7428-2.5 10.5 2.5 637.5 2.5 2.50 1.25 625 khz 9.0 mhz 800.0 ns 55.0 ns 3d7428-4 13.0 4.0 1020 3.2 4.00 2.00 390 khz 5.6 mhz 1280.0 ns 88.0 ns 3d7428-5 15.0 5.0 1275 4.0 5.00 2.50 312 khz 4.5 mhz 1600.0 ns 110.0 ns 3d7428-7.5 20.0 7.5 1912.5 6.0 7.50 3.75 208 khz 3.0 mhz 2400.0 ns 165.0 ns 3d7428-10 23.5 10 2550 8.0 10.0 5.00 156 khz 2.2 mhz 3200.0 ns 220.0 ns 3d7428-15 33.0 15 3825 12 15.0 9.00 104 khz 1.5 mhz 4800.0 ns 330.0 ns 3d7428-20 42.0 20 5100 16 20.0 12.0 78 khz 1.1 mhz 6400.0 ns 440.0 ns notes: a n y delay increment betw een 0.25 and 20 ns not show n is also av ailable as standard. see application notes section for more details ? 2004 data delay dev i ces doc #03003 data delay devices, inc. 1 5/8/2006 3 mt. prospect ave. clifton, nj 07013
3d7428 application notes the inherent delay error is the deviation of the inherent delay from its nominal value. it is limited to 1.0 lsb or 2.0 ns, whichever is greater. general information the 8-bit programmable 3d7428 delay line architecture is comprised of a number of delay cells connected in series with their respective outputs multiplexed onto the delay out pin (out) by the user-selected programming data (the address). each delay cell produces at its output a replica of the signal present at its input, shifted in time. the change in delay from one address setting to the next is called the increm ent , or lsb. it is nominally equal to the device dash number. the minimum delay, achieved by setting the address to zero, is called the inherent delay . delay stability the delay of cmos integrated circuits is strongly dependent on power supply and temperature. the 3d7428 utilizes novel compensation circuitry to minimize the delay variations induced by fluctuations in power s upply and/or temperature. with regard to stability, the delay of the 3d7428 at a given address, i, can be split into two components: the inherent delay (t 0 ) and the relative delay (t i ? t 0 ). these components exhibit very different stability coefficients, both of which must be considered in very critical applications. for best performance, it is essential that the power supply pin be adequately bypassed and filtered. in addition, the power bus should be of as low an impedance construction as possible. power planes are preferred. also, signal traces should be kept as short as possible. the thermal coefficient of the relative delay is limited to 250 ppm/c, which is equivalent to a variation, over the -40c to 85c operating range, of 1.5% from the room-temperature delay settings. this holds for all dash numbers. the thermal coefficient of the inherent delay is nominally +10ps/c for dash numbers less than 1, and +15ps/c for all other dash numbers. delay accuracy there are a number of ways of characterizing the delay accuracy of a programmable line. the first is the differential nonlinearity (dnl), also referred to as the increment error. it is defined as the deviation of the increment at a given address from its nominal value. for most dash numbers, the dnl is within 0.5 lsb at every address (see table 1: delay step). the power supply sensitivity of the relative delay is 0.5% over the 4.75v to 5.25v operating range, with respect to the delay settings at the nominal 5.0v power supply. this holds for all dash numbers. the sensitivity of the inherent delay is nominally ?1ps/mv for all dash numbers. the integrated nonlinearity (inl) is determined by first constructing t he least-squares best fit straight line through the delay-versus-address data. the inl is then the deviation of a given delay from this line. for all dash numbers, the inl is within 1.0 lsb at every address. input signal characteristics the frequency and/or pulse width (high or low) of operation may adversely impact the specified delay and increment accuracy of the particular device. the reasons for the dependency of the output delay accuracy on the input signal characteristics are varied and complex. therefore a recommended maximum and an absolute maximum operating input frequency and a recommended minimum and an absolute minimum operating pulse width have been specified. the relative error is defined as follows: e rel = (t i ? t 0 ) ? i * t inc where i is the address, t i is the measured delay at the i?th address, t 0 is the measured inherent delay, and t inc is the nominal increment. it is very similar to the inl, but simpler to calculate. for most dash numbers, the relative error is less than 1.0 lsb at every address (see table 1: delay range). operating frequency the absolute maximum operating frequency specification, tabulated in table 1, determines the highest frequency of the delay line input signal that can be reproduced, shifted in time at the device output, with acceptable duty cycle the absolute error is defined as follows: e abs = t i ? (t inh + i * t inc ) where t inh is the nominal inherent delay. the absolute error is limited to 1.5 lsb or 3.0 ns, whichever is greater, at every address. doc #03003 data delay devices, inc. 2 5/8/2006 tel: 973-773-2299 fax: 973-773-9672 http://www.datadelay.com
3d7428 application notes (cont?d) distortion. exceeding this limit will generally result in no signal output. the recommended maximum operating frequency specification determines the highest frequency of the delay line input signal for which the output delay accuracy is guaranteed. exceeding this limit (while remaining within the absolute limit) may cause some delays to shift with respect to their values at low frequency. the amount of delay shift will depend on the degree to which the limit is exceeded. to guarantee (if possible) the table 1 delay accuracy for input frequencies higher than the recommended maximum frequency, the 3d7428 must be tested at the user operating frequency. in this case, to facilitate production and device identification, the part number will include a custom reference designator identifying the intended frequency of operation. the programmed delay accuracy of the device is guaranteed, therefore, only at the user specified input frequency. small input frequency variation about the selected frequency will only marginally impact the programmed delay accuracy, if at all. contact the factory for details. operating pulse width the absolute minimum operating pulse width (high or low) specification, tabulated in table 1, determines the smallest pul se width of the delay line input signal that can be reproduced, shifted in time at the device output, with acceptable pulse width distortion. exceeding this limit will generally result in no signal output. the recommended minimum operating pulse width (high or low) specification determines the smallest pulse width of the delay line input signal for which the output delay accuracy tabulated in table 1 is guaranteed. exceeding this limit (while remaining within the absolute limit) may cause s o me delays to s h ift with res pec t to their values at long pulse width. the amount of delay shift will depend on the degree to which the limit is exceeded. to guarantee the table 1 delay accuracy for input pulse width smaller than the recommended minimum operating pulse width, the 3d7428 must be tested at the user operating pulse width. in this case, to facilitate production and device identification, the part number will include a custom reference designator identifying the intended frequency and duty cycle of operation. the programmed delay accuracy of the device is guaranteed, therefore, only for the user specified input characteristics. small input pulse width variation about the selected pulse width will only marginally impact the programmed delay accuracy , if at all. programmed delay update a delay line is a memory device. it stores information present at the input for a time equal to the delay setting before presenting it at the output with minimal distortion. the 3d7428 8-bit programmable delay line can be represented by 256 serially connected delay elements (individually addressed by the programming data), each capable of storing data for a time equal to the device increment (step time). the delay line memory property, in conjunction with the operational requirem ent of ?instantaneously? connecting the delay element addressed by the programming data to the output, may inject spurious information ont o the output data stream. in order to ensure that spurious outputs do not occur, it is essential that the input signal be idle (held high or low) for a short duration prior to updating the programmed delay. this duration is given by the maximum programmable delay. satisfying this requirement allows the delay line to ?clear? itself of spurious edges. when the new address is loaded, the input signal can begin to switch (and the new delay will be valid) after a time given by t pdv or t edv (see section below). programming interface figure 1 illustrates the main functional blocks of the 3d7428 delay program interface. since the 3d7428 is a cmos design, all unused input pins must be returned to well defined logic levels, vdd or ground. transparent parallel mode (md = 1, ae = 1) the eight program pins p0 - p7 directly control the output delay. a change on one or more of the program pins will be reflected on the output delay after a time t pdv , as shown in figure 2. a register is required if the programming data is bused. doc #03003 data delay devices, inc. 3 5/8/2006 3 mt. prospect ave. clifton, nj 07013
3d7428 application notes (cont?d) latched parallel mode (md = 1, ae pulsed) the eight program pins p0 - p7 are loaded by the falling edge of the enable pulse, as shown in figure 3. after each change in delay value, a s e ttling time t edv is required before the input is accurately delayed. serial mode (md = 0) while observing data setup ( t dsc ) and data hold ( t dhc ) requirements, timing data is loaded in msb-to-lsb order by the rising edge of the clock (sc) while the enable (ae) is high, as shown in figure 4. the falling edge of the enable (ae) activates the new delay value which is reflected at the output after a settling time t edv . as data is shifted into the serial data input (si), the previous contents of the 8-bit input register are shifted out of the serial output port pin (so) in msb-to-lsb order, thus allowing cascading of multiple devices by connecting the serial output pin (so) of the preceding device to the serial data input pin (si) of the succeeding device, as illustrated in figure 5. the total number of serial data bits in a cascade configuration must be eight times the number of units, and each group of eight bits must be transmitted in msb-to-lsb order. to initiate a serial read, enable (ae) is driven high. after a time t eqv , bit 7 (msb) is valid at the serial output port pin (so). on the first rising edge of the serial clock (sc), bit 7 is loaded with the value present at the serial data input pin (si), while bit 6 is presented at the serial output pin (so). to retrieve the remaining bits s e ven more rising edges must be generated on the serial clock line. the read operation is destructive. therefore, if it is desired that the original delay setting remain unchanged, the read data must be written back to the device(s) before the enable (ae) pin is brought low. the so pin, if unused, must be allowed to float if the device is configured in the serial programming mode. the serial mode is the only mode available on the 8-pin version of the 3d7428. pr o g r amm able d e lay line la t ch 8 - bi t i n pu t re gist e r md sc si a e in so out p0 p1 p2 p3 p4 p5 p6 p7 m o de s e le ct shi ft cloc k ser i a l i n pu t a d d r es s en ab l e si gn al i n si gn al ou t se r i a l ou t p u t p a ra lle l i n p u t s figur e 1 : func tion a l bloc k dia g r a m pr eviou s pr eviou s ne w v a l ue ne w v a l ue t pdx t pd v par all e l in pu ts p0- p 7 de l a y tim e figur e 2 : non-l a tc he d pa ra ll e l mode (m d= 1 , a e = 1 ) doc #03003 data delay devices, inc. 4 5/8/2006 tel: 973-773-2299 fax: 973-773-9672 http://www.datadelay.com
3d7428 doc #03003 data delay devices, inc. 5 5/8/2006 3 mt. prospect ave. clifton, nj 07013 application notes (cont?d) pr e v iou s ne w v a lue ne w v a lue t ed x t ed v para l le l in pu ts p0-p7 d e lay tim e t dse t dh e t ew en ab l e (a e ) figure 3 : la tc he d pa ra lle l mode (m d= 1 ) ne w val ue ne w bi t 7 new bi t 0 new bi t 6 ol d bi t 7 ol d bi t 6 ol d bi t 0 enab le ( ae) clo ck (s c) se r i al in pu t ( si ) se r i al out p ut ( so ) de la y ti m e t ew t es t cw t cw t eh t dsc t dhc t eg v t cqv t cq x t eq z t edv t edx pr evio u s val u e fi gu r e 4 : s e r i a l m ode (m d= 0 ) from w r it in g devi ce to ne xt de vi ce si so sc a e 3d7 428 3 d 742 8 3d 7428 f i g u re 5 : c ascad in g m u lt i p le d e v i ce s si so sc a e si so sc a e table 2: delay vs. programmed address p r o g r a m m e d a d d r e s s p a r a l l e l p 7 p 6 p 5 p 4 p 3 p 2 p 1 p 0 nominal delay (ns) per 3d7428 dash number serial ms b lsb - 0 . 2 5 - 0 . 5 - 1 - 2 - 5 - 1 0 - 2 0 s t e p 0 0 0 0 0 0 0 0 0 1 0 . 5 0 1 0 . 5 1 0 . 5 1 0 . 5 1 5 2 3 . 5 4 2 s t e p 1 0 0 0 0 0 0 0 1 1 0 . 7 5 1 1 . 0 1 1 . 5 1 2 . 5 2 0 3 3 . 5 6 2 s t e p 2 0 0 0 0 0 0 1 0 1 1 . 0 0 1 1 . 5 1 2 . 5 1 4 . 5 2 5 4 3 . 5 8 2 s t e p 3 0 0 0 0 0 0 1 1 1 1 . 2 5 1 2 . 0 1 3 . 5 1 6 . 5 3 0 5 3 . 5 1 0 2 s t e p 4 0 0 0 0 0 1 0 0 1 1 . 5 0 1 2 . 5 1 4 . 5 1 8 . 5 3 5 6 3 . 5 1 2 2 s t e p 5 0 0 0 0 0 1 0 1 1 1 . 7 5 1 3 . 0 1 5 . 5 2 0 . 5 4 0 7 3 . 5 1 4 2 step 2 5 3 1 1 1 1 1 1 0 1 7 3 . 7 5 1 3 7 . 0 2 6 3 . 5 5 1 6 . 5 1 2 8 0 2 5 5 3 . 5 5 1 0 2 step 2 5 4 1 1 1 1 1 1 1 0 7 4 . 0 0 1 3 7 . 5 2 6 4 . 5 5 1 8 . 5 1 2 8 5 2 5 6 3 . 5 5 1 2 2 step 2 5 5 1 1 1 1 1 1 1 1 7 4 . 2 5 1 3 8 . 0 2 6 5 . 5 5 2 0 . 5 1 2 9 0 2 5 7 3 . 5 5 1 4 2 c h a n g e 6 3 . 7 5 1 2 7 . 5 2 5 5 . 0 5 1 0 . 0 1 2 7 5 2 5 5 0 . 0 5 1 0 0
3d7428 device specifications table 3: absolute maximum ratings p a r a m e t e r s y m b o l m i n m a x u n i t s n o t e s dc supply voltage v dd - 0 . 3 7 . 0 v input pin voltage v in - 0 . 3 v dd +0. 3 v input pin current i in - 1 0 1 0 m a 2 5 c storage temperature t st rg - 5 5 1 5 0 c lead temperature t lead 3 0 0 c 1 0 s e c table 4: dc electrical characteristics (-40c to 85c, 4.75v to 5.25v) p a r a m e t e r s y m b o l m i n t y p m a x u n i t s n o t e s static supply current* i dd 3 . 0 5 . 0 m a high level input voltage v ih 2 . 0 v low level input voltage v il 0 . 8 v high level input current i ih 1 . 0 a v ih = v dd low level input current i il 1 . 0 a v il = 0v high level output current i oh - 3 5 . 0 - 4 . 0 m a v dd = 4.75v v oh = 2.4v low level output current i ol 4 . 0 1 5 . 0 m a v dd = 4.75v v ol = 0.4v output rise & fall time t r & t f 2 . 0 2 . 5 n s c ld = 5 pf *i dd (dy nami c ) = c ld * v dd * f input capacitance = 10 pf ty pical w here: c ld = average capacitance load/line (pf) output load capacitance (c ld ) = 25 pf max f = input frequency (ghz) table 5: ac electrical characteristics (-40c to 85c, 4.75v to 5.25v) p a r a m e t e r s y m b o l m i n t y p m a x u n i t s n o t e s clock frequency f c 8 0 m h z enable width t ew 1 0 n s clock width t cw 1 0 n s data setup to cloc k t dsc 1 0 n s data hold from cloc k t dhc 3 n s data setup to enable t dse 1 0 n s data hold from enable t dhe 3 n s enable to serial output valid t eqv 2 0 n s enable to serial output high-z t eqz 2 0 n s clock to serial output valid t cqv 2 0 n s cloc k to serial output invalid t cqx 1 0 n s enable setup to clock t es 1 0 n s enable hold from clock t eh 1 0 n s parallel input valid to delay valid t pdv 2 0 4 0 n s 1 parallel input change to delay invalid t pdx 0 n s 1 enable to delay valid t edv 3 5 4 5 n s 1 enable to delay invalid t edx 0 n s 1 input pulse width t wi 8 % of total delay see table 1 input period period 20 % of total delay see table 1 input to output delay t plh , t phl ns see table 2 notes: 1 - refer to programmed delay update sect ion doc #03003 data delay devices, inc. 6 5/8/2006 tel: 973-773-2299 fax: 973-773-9672 http://www.datadelay.com
3d7428 silicon delay line automated testing test conditions input: output: ambient temperature: 25 o c 3 o c r load : 10k ? 10% supply voltage (vcc): 5.0v 0.1v c load : 5pf 10% input pulse: high = 3.0v 0.1v threshold: 1.5v (rising & falling) low = 0.0v 0.1v source impedance: 50 ? max. 10k ? 470 ? 5pf dev i c e under te s t di gi t a l s c ope rise/fall time: 3.0 ns max. (measured between 0.6v and 2.4v ) pulse width: pw in = 1.25 x total delay period: per in = 2.5 x total delay note: the above conditions are for test only and do not in any way restrict the operation of the device. ou t tri g in ref tr ig f i g u re 6: t e st set u p de v i ce un de r test ( d ut) dig i tal s c ope/ ti m e i n te r v a l cou n ter pu lse ge ne ra to r ou t in com p u t e r sys tem pr in te r figur e 7 : t i ming dia g r a m t plh t phl per in pw in t rise t fall 0. 6 0. 6 1. 5 1. 5 2. 4 2 . 4 1. 5 1. 5 v ih v il v oh v ol inp u t si g n al out p ut si g n al doc #03003 data delay devices, inc. 7 5/8/2006 3 mt. prospect ave. clifton, nj 07013
|
